YUKEN日本品牌DSG-005系列電磁換向閥資料

上海乾拓貿易有限公司

聯系人：楊江玲

企業QQ：2880626083

手 機：18917074297（微信）

電 話：021-39529830-8012

郵箱；18917074297@163.com

地址：上海市嘉定區江橋嘉涌路6號樓713室   

manufactured but enjoy a maximum operating pressure of 25 MPa (3630 PSI) and a maximum 

flow rate of 10 L/min (2.6 U.S.GPM), while contributing further to a space saving requirement.

  Moreover, using wet armature solenoids, the valves ensure the long life.

Special Seals F: Special seals for  phosphate ester  type fluids  (Omit if not  required) 

Up to 25 MPa (3630 PSI), 10 L/min (2.6 U.S.GPM)

Sub-plates are available. Specify the sub-plate model number from the table above.  

When sub-plates are not used, the mounting surface should have a good machined finish.

These DSG-005 series solenoid operated directional valves are the pro- ducts newly developed 

Due caution must be paid to maintaining control over contamination of the hydraulic fluids 

which may otherwise lead t o breakdowns and shorten the life of the valve. 

Sub-plate Mounting DIRECTIONAL VALVES DSG-005-???-?-30/3090

The maximum flow means the limited flow without inducing any abnormality to the operation

Always be sure to use hydraulic fluids within the stipulated conditions shown below:  

2  Viscosity:  20-200 mm /s (100-930 SSU), Temperature:  -15 to+60°C (5 to 140°F). 

Recommended Viscosity and Oil Temperatures

 Use 20 μm or finer line filter. Control of Contamination

 compactly manufactured but enjoy a maximum operating pressure of 25 MPa (3630 PSI)

Model Number Designation DSG -005 -3 C 2 -D24 -30 ? Series Number Valve Size Number 

40DSG: Solenoid Operated  Directional Valve 005 3 2 C: Spring Centred B: Spring Offset 2,

 3 AC  A100, A200  DC  D12, D24 30 Refer to 

These DSG-005 series solenoid operated directional valves are the pro- ducts newly developed 

as a "Mini-series".  Compared with DSG-01 series, t he valves are much more compactly 

For details, please refer to the "List of Standard Models and Maximum Flow" on pages 3 and 4.

Inrush current in the above table shows rms values at maximum stroke.

Design Standards: None.........Japanese Standard "JIS" and European Design Standard 90 . N. American Design Standard

Fluid Types Hydraulic Fluids Any type of hydraulic fluid listed in the table below can be used.

Mounting Bolts Four socket head cap screws in the table below are included.

 Please maintain the degree of contamination within NAS 1638-Grade 1 1. 

 (changeover) of the valve.  The maximum flow differs according to the spool type and operating conditions.  

 and a maximum flow rate of 10 L/min (2.6 U.S.GPM), while contributing further to a space saving requirement.  

Moreover, using wet armature solenoids, the valves ensure the long life.

MPa (PSI) MPa (PSI) -1  min (Cycles/min)

of Valve Position Spool-Spring  Arrangement Spool Type Coil Type Design  Number Design  Standard 2, 3 

as a "Mini-series".  Compared with DSG-01 series, t he valves are much more

YUKEN日本品牌DSG-005系列電磁換向閥資料